Hallo Ketemu lagi dengan Saya disini saya akan menjelaskan tentang Cara Konfigurasi VLAN Di Cisco Packet Tracer, Sebelum menuju konfigurasi lebih lanjut perhatikan gambar diatas.
Yang akan kita gunakan untuk konfigurasi, Diantaranya adalah :
1 Router
4 PC
2 Switch
Kabel Crossover
Kabel Straight
Jika sudah Seperti topologi di atas Lanjut kita Konfigurasi VLAN Di Cisco Packet Tracer , Yang pertama kita Konfig adalah IP Pada masing masing PC Pada Grup 1
PC-reckzone IP : 192.168.9.1 / Netmask 255.255.255.0 / Gateway 192.168.9.254
PC2-reckzone IP : 192.168.9.2 / Netmask 255.255.255.0 / Gateway 192.168.9.254
PC-bagas IP : 192.168.10.1 / Netmask 255.255.255.0 / Gateway 192.168.10.254
PC2-bagas IP : 192.168.10.2 / Netmask 255.255.255.0 / Gateway 192.168.10.254
Jika sudah Config IP Pada Konfigurasi VLAN Di Cisco Packet Tracer Selanjutnya sekarang kita Konfigurasi Switch pada Grup 1 Vlan
Click Switch0 > CLI
Switch>enable
Switch#
%SYS-5-CONFIG_I: Configured from console by console
Switch#vlan database
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 10 name reckzone
VLAN 10 added:
Name: reckzone
Switch(vlan)#vlan 20 name bagas
VLAN 20 added:
Name: bagas
Switch(vlan)#exit
APPLY completed.
Exiting....
Switch#int
Switch#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int f0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#int f0/2
Switch(config-if)#switchport mode acc
Switch(config-if)#switchport access vlan 20
Switch(config-if)#exit
Switch(config)#int gi0/2
Switch(config-if)#switchport mode trunk
Switch(config-if)#end
Switch#
%SYS-5-CONFIG_I: Configured from console by console
Click Switch1 > CLI
Switch>ena
Switch#vlan data
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 10 name reckzone
VLAN 10 added:
Name: reckzone
Switch(vlan)#vlan 20 name bagas
VLAN 20 added:
Name: bagas
Switch(vlan)#exit
APPLY completed.
Exiting....
Switch#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int fa0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 10
Switch(config-if)#exit
Switch(config)#interface fastEthernet 0/2
Switch(config-if)#switchport mode access
Switch(config-if)#swit acc vlan 20
Switch(config-if)#exit
Switch(config)#int gi0/1
Switch(config-if)#switchport mode trunk
Click Router0 > CLI
Router>ena
Router#conf ter
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g0/0
Router(config-if)#no sh
Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int g0/0.1
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.1, changed state to up
Router(config-subif)#encapsulation dot1Q 1
Router(config-subif)#ip add 192.168.9.254 255.255.255.0
Router(config-subif)#exit
Router(config)#int g0/0.2
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.2, changed state to up
Router(config-subif)#encapsulation dot1Q 2
Router(config-subif)#ip add 192.168.10.254 255.255.255.0
Router(config-subif)#exit
Router(config)#end
Jika sudah sekarang kita test PING pc-reckzone dangan pc2-reckzone,pc-bagas dengan pc2-bagas
Lihat di gambar , kalau sukses Hasilnya
Sekian Dari saya , Mohon Maaf Kalau kurang jelas :)
Download File Sudah Jadi Klik Dsini
0 komentar